|
Viewing Auto Body >> Body and Fender >> Dent Repair Kits Inflatable Dent Repair Kit
Built in hand pumps prompte a high degree of control. This kit includes an 8" square and 8-1/2" x 14-1/2" heat welded reinforced bladder. Thin enough (about 1/8") to slide into a door glass opening or small hole. Strong enough to withstand years of use. A great tool for paintless dent repair. Made in the USA.
Uni Spot Stud Welder9-Finger Pull Claw 1/2lb Wire
This Stud Welder has a million weld lifespan with an innovative transformer design that produces 2700 amps for a fraction of a second gets the job done with minimal heat spread. Includes an easy release slide hammer with ergonomic "T" handle, mini-puller, stud welding tip, molding rivet tip, shrink tip, eliminator, 200 pcs. 2.2mm "Flexpert" studs, 200 pcs. 2.2mm "Blackhead" studs, 50 pcs. Molding studs, custom molded toolbox and instructions. Made in Canada.
Inflatable Dent Remover/Oval
Built in hand pump promotes a high degree of control. This 8-1/2" by 14-1/2" oval bladder features heat welded seams. Thin enough (about 1/8" thick) to slide into a door glass opening or small hole. Strong enough to withstand years of use. A great tool for paintless dent repair. Made in the USA.
Inflatable Dent Remover/Square
Built in hand pump provides a high degree of control. This 8" square bladder features heat welded seams for durability. Thin enough when bladder is deflated (about 1/8") to slide into a door glass opening or small hole. Strong enough to withstand years of use. A great tool for paintless dent repair. Made in the USA.
Magna Wire Electrode kit
Magna Wire Electrode Kit - Replaces the outer nose and central electrode on the (31123) and (31041) Stud Welders to install the Magna Wire. The Magna Wire (31181) is welded along a crease to make pulling easy with either the Magna Clamp (31183) with your frame machine or with the 5-Finger Magna Claw (31180). The Magna Claw can be used with a slide hammer, frame machine, or by hand with the screw-in handle.
Shoot Suit Welded Stud Puller
Designed to be used with the Stud Welder System, this tool makes it easy to repair minor dings and dents, due to hail, parking lots, etc. Just weld a draw-pin (stud) to the surface, attach the tool to the pin, slowly squeeze the handles until the dent is flush with the surface, then snip-off the draw pin.
10/pak Glue Sticks for Prof Dent Repair IR Kit
Glue Sticks for the (52230) Professional Paintless Dent Repair Kit - This pack contains 10 tan 1/2" diameter by 10" long glue sticks for use in the glue gun included in the Professioanl Paintless Dent Repair Kit.
Rivet Puller
The Rivet Puller fits under the head of the Trim Rivets (31041D) to pull dents where the trim is fastened.
Dent Killer
A precision pulling tool for use with our stud welders and others with 1" OD grounding ring. Just seat the stud welder in the Dent Killer, bring grounding rods into surface contact and trigger your stud welding gun for.5-1 seconds to attach the reusable "stud". Raise metal with the attached 3:1 lever for exactly the right amount of pull to achieve a level surface. Nylon faced 5-1/2" long support legs adjust from 3" to 7" to span damage & styling lines. Rotate the tool to release the stud. Great for use along creases or in areas without enough overhead clearance to use a sliding hammer. Imported.
|